0

Your Cart is Empty

Shop by Part
Brands
Install Guides

Install Guide

How to Install Lower Trailing Arms on a Toyota Tundra

Nov 18, 2026 · 3 min read

Lower trailing arm installed on a Toyota Tundra

High Road Suspension recommends a certified technician install this system. In addition to these instructions, professional knowledge of disassembly and reassembly procedures, as well as post-installation checks, must be known.

This is the same process for the 2024+ Toyota Land Cruiser LC250, 2024+ Toyota Tacoma, 2025+ Toyota 4Runner, 2022+ Toyota Tundra, and 2023+ Toyota Sequoia. Socket sizes may differ.

Suggested Tools

  • Wheel chocks
  • Grease gun
  • Torque wrench
  • 22mm socket
  • 18mm socket
  • 18mm wrench
  • Grease (Lucas "Red 'N' Tacky" grease recommended)

Installation

  1. There is no need to place the vehicle on jack stands for this job.
  2. Set the parking brake.
  3. Chock the rear tires to prevent rolling.
  4. Using a 22mm socket, remove the rear tires and wheels.
  5. Working on one side at a time, use an 18mm socket and 18mm wrench to remove the front and rear lower trailing arm bolts and detach the factory trailing arm. Retain the OEM bolts for reinstallation.
  6. If one end or both ends of the trailing arm has a bushing, grease the ends with a grease gun through the supplied zerk fittings. We like to use Lucas "Red 'N' Tacky" grease. If both ends of the trailing arm have heim ends, there is no need to grease them, because the uniball in the heim end is lined with Teflon, so no grease is required.
  7. The larger, more offset end of the trailing arm mounts at the bottom mounting point.
  8. Reuse the OEM bolts and mounting hardware. Hand tighten initially.
  9. Repeat the process on the opposite side.
  10. Using the 18mm socket with a torque wrench and an 18mm wrench, torque all bolts to the factory-recommended 73 lb of torque once both sides are installed.

Post-Installation

  • Check and recheck all fasteners for proper torque.
  • Check to ensure there is adequate clearance between all rotating, mobile, fixed, and heated members.
  • Check the clearance between the sidewall of the tire and surrounding components.
  • Re-torque all fasteners after 500 miles. Visually inspect components and re-torque fasteners during routine vehicle service.
  • Adjust the headlights to the proper settings given the increased vehicle height.

Maintenance Information

It is the ultimate buyer's responsibility to have all bolts and nuts checked for tightness after the first 500 miles, and then every 1000 miles. The wheel alignment, steering system, suspension, and driveline systems must be inspected by a qualified professional mechanic at least every 3000 miles.

Shop suspension and lift components for the 2022+ Toyota Tundra.

Frequently Asked Questions

What vehicles does this trailing arm installation apply to?

The process shown here for the Toyota Tundra is the same for the 2024+ Toyota Land Cruiser LC250, 2024+ Toyota Tacoma, 2025+ Toyota 4Runner, 2022+ Toyota Tundra, and 2023+ Toyota Sequoia. The socket sizes may differ between platforms, but the steps are the same.

Do I need to grease the trailing arms?

Only if they have bushing ends. If one or both ends use a bushing, grease them through the supplied zerk fittings with a grease gun. We like Lucas "Red 'N' Tacky" grease. If both ends are heim ends, no grease is needed, because the uniball in the heim end is lined with Teflon.

Which way do the trailing arms mount?

The larger, more offset end of the trailing arm mounts at the bottom mounting point. Reuse the OEM bolts and mounting hardware, hand tighten first, and do the final torque once both sides are installed.

What torque do the trailing arm bolts need?

Torque all bolts to the factory-recommended 73 lb once both sides are installed. Re-torque all fasteners after the first 500 miles, and check them again during routine service.

Do I need to put the truck on jack stands for this install?

No. This job does not require jack stands. You set the parking brake, chock the rear tires, remove the rear wheels with a 22mm socket, and work one side at a time.